160M3 AWD Motor Grader

Specifications

Select Units

US
Metric

Overview

The M Series 3 brings the latest emissions reduction technology to the most durable, productive and comfortable motor graders on the market. From building roads to maintaining them, M Series Motor Graders are designed to help you get more work done in less time. Outstanding durability, unprecedented operator comfort and ease of service help to maximize your return on investment. M Series 3 Motor Graders meet U.S. EPA Tier 4 Final/EU Stage IV emission standards.

Engine

Power Train

Forward/Reverse Gears 8 Forward/6 Reverse 8 Forward/6 Reverse
Transmission APECS, Direct Drive, Powershift APECS, Direct Drive, Powershift
Brakes - Service Multiple Oil Disc Multiple Oil Disc
Brakes - Service - Surface Area 3565.0 in² 23000.0 cm²
Brakes - Parking Multiple Oil Disc Multiple Oil Disc
Brakes - Secondary Dual Circuit Control Dual Circuit Control

Hydraulic System

Circuit Type Parallel Parallel
Pump Type Variable Piston Variable Piston
Pump Output 55.5 gal/min 210.0 l/min
Maximum System Pressure 3503.0 psi 24150.0 kPa
Reservoir Tank Capacity 16.9 gal (US) 64.0 l
Standby Pressure 885.0 psi 6100.0 kPa

Operating Specifications

Top Speed - Forward 29.5 mile/h 47.4 km/h
Top Speed - Reverse 23.3 mile/h 37.4 km/h
Turning Radius - Outside Front Tires 25.59 ft 7.8 m
Steering Range - Left/Right 50° 50°
Articulation Angle - Left/Right 20° 20°
Forward - 1st 2.6 mile/h 4.1 km/h
Forward - 2nd 3.5 mile/h 5.6 km/h
Forward - 3rd 5.1 mile/h 8.1 km/h
Forward - 4th 7.0 mile/h 11.2 km/h
Forward - 5th 10.8 mile/h 17.4 km/h
Forward - 6th 14.7 mile/h 23.7 km/h
Forward - 7th 20.3 mile/h 32.6 km/h
Forward - 8th 29.5 mile/h 47.4 km/h
Reverse - 1st 2.0 mile/h 3.3 km/h
Reverse - 2nd 3.8 mile/h 6.1 km/h
Reverse - 3rd 5.5 mile/h 8.8 km/h
Reverse - 4th 8.5 mile/h 13.7 km/h
Reverse - 5th 16.0 mile/h 25.7 km/h
Reverse - 6th 23.3 mile/h 37.4 km/h

Service Refill

Fuel Capacity 104.0 gal (US) 394.0 l
Cooling System 15.0 gal (US) 57.0 l
Hydraulic System - Total 26.4 gal (US) 100.0 l
Hydraulic System - Tank 16.9 gal (US) 64.0 l
Diesel Exhaust Fluid 5.8 gal (US) 22.0 l
Transmission - Differential - Final Drives 18.5 gal (US) 70.0 l
Engine Oil 7.9 gal (US) 30.0 l
Tandem Housing - Each 22.9 gal (US) 87.0 l
Front Wheel Spindle Bearing Housing 0.13 gal (US) 0.5 l
Circle Drive Housing 1.8 gal (US) 7.0 l

Frame

Drawbar - Width 3.0 in 76.2 mm
Circle - Diameter 61.1 in 1553.0 mm
Circle - Blade Beam Thickness 1.6 in 40.0 mm
Drawbar - Height 6.0 in 152.0 mm
Circle - Height 6.3 in 160.0 mm
Front Frame Structure - Height 12.6 in 321.0 mm
Front Frame Structure - Width 12.0 in 305.0 mm
Drawbar - Thickness 0.5 in 12.7 mm
Front-Top/Bottom Plate - Width 12.0 in 305.0 mm
Front-Top/Bottom Plate - Thickness 0.87 in 22.0 mm
Front Axle - Height to Center 23.5 in 596.0 mm
Front Axle - Wheel Lean - Left/Right 18° 18°
Front Axle - Total Oscillation per Side 32° 32°

Tandems

Height 22.5 in 572.0 mm
Width 8.0 in 204.0 mm
Sidewall Thickness - Inner 0.69 in 17.5 mm
Sidewall Thickness - Outer 0.71 in 18.0 mm
Drive Chain Pitch 2.0 in 50.8 mm
Wheel Axle Spacing 60.0 in 1523.0 mm
Tandem Oscillation - Front Up 15° 15°
Tandem Oscillation - Front Down 25° 25°

Moldboard

Blade Width 14.0 ft 4.2 m
Moldboard - Height 24.0 in 610.0 mm
Moldboard - Thickness 0.87 in 22.0 mm
Arc Radius 16.3 in 413.0 mm
Throat Clearance 6.5 in 166.0 mm
Cutting Edge Width 6.0 in 152.0 mm
Cutting Edge Thickness 0.6 in 16.0 mm
End Bit - Width 6.0 in 152.0 mm
End Bit - Thickness 0.6 in 16.0 mm
Blade Pull - Base GVW - AWD 36817.0 lb 16700.0 kg
Blade Pull - Maximum GVW - AWD 49630.0 lb 22512.0 kg
Blade Down Pressure - Base GVW - AWD 18935.0 lb 8589.0 kg
Blade Down Pressure - Maximum GVW - AWD 29308.0 lb 13294.0 kg
Moldboard - Blade Width 14.0 ft 4.2 m

Blade Range

Circle Centershift - Right 28.7 in 728.0 mm
Circle Centershift - Left 27.4 in 695.0 mm
Moldboard Sideshift - Right 26.0 in 660.0 mm
Moldboard Sideshift - Left 20.1 in 510.0 mm
Maximum Blade Position Angle 90° 90°
Blade Tip Range - Forward 40° 40°
Blade Tip Range - Backward 5° 5°
Maximum Lift Above Ground 17.8 in 452.0 mm
Maximum Depth of Cut 29.5 in 750.0 mm
Maximum Shoulder Reach Outside of Tires - Left 82.3 in 2090.0 mm
Maximum Shoulder Reach Outside of Tires - Right 89.7 in 2278.0 mm

Ripper

Ripper Shank Holder Spacing 21.0 in 533.0 mm
Ripping Depth - Maximum 16.8 in 426.0 mm
Ripper Shank Holders 5 5
Penetration Force 20812.0 lb 9440.0 kg
Pry-Out Force 28493.0 lb 12924.0 kg
Machine Length Increase, Beam Raised 40.6 in 1031.0 mm

Scarifier

Front, V-Type - Working Width 47.4 in 1205.0 mm
Front, V-Type, 5 or 11 Tooth - Scarifier Shank Holder Spacing 4.6 in 116.0 mm
Front, V-Type, 5 or 11 Tooth - Scarifier Shank Holders 5/11 5/11
Front, V-Type, 5 or 11 Tooth - Scarifying Depth, Maximum 18.4 in 467.0 mm
Front, V-Type, 5 or 11 Tooth - Working Width 40.6 in 1031.0 mm
Mid, V-Type - Scarifier Shank Holder Spacing 4.6 in 116.0 mm
Mid, V-Type - Scarifier Shank Holders 11 11
Mid, V-Type - Scarifying Depth, Maximum 11.5 in 292.0 mm
Mid, V-Type - Working Width 46.6 in 1184.0 mm
Rear - Scarifying Depth, Maximum 16.8 in 426.0 mm
Rear - Working Width 84.0 in 2133.0 mm
Rear - Scarifier Shank Holders 9 9
Rear - Scarifier Shank Holder Spacing 10.5 in 267.0 mm

Weights

Operating Weight - Typically Equipped 47514.0 lb 21552.0 kg

Weights - AWD

Gross Vehicle Weight - Base - Front Axle 11033.0 lb 5004.0 kg
Gross Vehicle Weight - Base - Rear Axle 29875.0 lb 13551.0 kg
Gross Vehicle Weight - Base - Total 40908.0 lb 18555.0 kg
Gross Vehicle Weight - Maximum - Front Axle 17075.0 lb 7745.0 kg
Gross Vehicle Weight - Maximum - Rear Axle 38069.0 lb 17268.0 kg
Gross Vehicle Weight - Maximum - Total 55144.0 lb 25013.0 kg
Operating Weight - Typically Equipped - Front Axle 14289.0 lb 6481.0 kg
Operating Weight - Typically Equipped - Rear Axle 33225.0 lb 15071.0 kg
Operating Weight - Typically Equipped - Total 47514.0 lb 21552.0 kg

Dimensions

Height - Top of Cab 130.0 in 3308.0 mm
Length - Counterweight to Ripper 399.0 in 10136.0 mm
Width - Outside Front Tires 98.9 in 2511.0 mm
Length - Front Axle to Mid Tandem 241.0 in 6123.0 mm
Length - Front Tire to Rear of Machine 351.0 in 8912.0 mm
Length - Front Axle to Moldboard 100.0 in 2552.0 mm
Length - Between Tandem Axles 60.0 in 1523.0 mm
Width - Outside Rear Tires 98.9 in 2511.0 mm
Width - Tire Center Lines 84.3 in 2140.0 mm
Height - Front Axle Center 23.5 in 596.0 mm
Height - Exhaust Stack 128.0 in 3256.0 mm
Height - Top of Cylinders 120.0 in 3040.0 mm
Ground Clearance - Rear Axle 13.3 in 339.0 mm

Standards

Brakes ISO 3450 ISO 3450
ROPS/FOPS ISO 3471; ISO 3499 ISO 3471; ISO 3499
Sound ISO 6394; ISO 6395 ISO 6394; ISO 6395
Steering ISO 5010 ISO 5010

Benefits & Features

Operator Station

Visibility

Good visibility is key to your safety and efficiency. Angled cab doors, tapered engine enclosure and a sloped rear window make it easy to see the moldboard and tires, as well as behind the machine. An optional rear vision camera further enhances lines of sight all around the machine.

In-Dash Instrument Cluster

A redesigned message display shows machine performance and diagnostic information, including DEF tank levels. Now located in the center console, it also displays Cat Grade Control Cross Slope readings conveniently in front of the operator.

Comfort and Control

Experience the most comfortable cab in the industry. Joystick controls replace levers, so hand and arm movement is reduced by 78%, helping reduce operator fatigue for better productivity. Rocker and control switches are in easy reach. An updated seat with softer cushions and three-position cushion tilt adds to your overall comfort. You can even upgrade to a heated or heated/ventilated seat. An optional seat belt indicator feature is also available. Control pods can be adjusted electronically, making it easy to set your ideal operating position. Multiple isolation mounts significantly reduce sound and vibration for a more relaxed work environment. The high capacity Heating, Ventilation and Air Conditioning (HVAC) system dehumidifies and pressurizes the cab, seals out dust and helps keep windows clear. Pop-out louvers circulate fresh air. An optional deluxe radio with CD features MP3 and Bluetooth technology.

Machine and Implement Controls

Two electro-hydraulic joysticks with electronically adjustable control pods help position operators for optimal comfort, visibility and productive operation.

Joystick Functions

The left joystick controls machine direction, steering, articulation, return-to-center, wheel lean, gear selection, left moldboard lift cylinder and float. The right joystick controls drawbar, circle and moldboard functions as well as electronic throttle control and manual differential lock/unlock. The steer tire angle matches the joystick position. A brake tensioning system holds the joystick in position until the operator moves it. The steering control automatically reduces steering sensitivity at higher ground speeds for predictable control. Infinitely variable roller switches control the rear ripper and/or front lift group (when equipped). Optional Programmable Auxiliary Hydraulic Pod controls up to six additional hydraulic circuits.

Electronic Throttle Control

Electronic Throttle Control helps improve productivity by providing the best match of horsepower and torque for the demands of the application.

Articulation Return-to-Center

Automatically returns the machine to a straight frame position from any angle with the touch of a button.

Selectable Blade Lift Modes

Choose the blade lift modulation mode that best fits your application or operating style: Fine, Normal, or Coarse.

Engine

A Cat C9.3 ACERT engine gives you the performance you need to maintain consistent grading speeds for maximum productivity. Every U.S. EPA Tier 4 Final/EU Stage IV ACERT engine is equipped with a combination of proven electronic, fuel, air and aftertreatment components. Applying proven technologies systematically and strategically helps meet your high expectations for productivity, fuel efficiency, reliability and service life.

Hydraulic Demand Fan

The hydraulic demand fan automatically adjusts speed according to cooling requirements. When cooling demand is reduced, you benefit from more power to the ground and improved fuel efficiency.

Engine Idle Shutdown Timer

This standard feature can be software-enabled by your Cat dealer to shut down the engine after a set period of time to save you fuel and help reduce emissions.

Emissions Technology

Emissions reduction technology on the M Series 3 Motor Grader is designed to be transparent, with no action required from the operator. There is no need to stop. Regeneration runs automatically at cold start-up and, if needed, in the background while you work.

Aftertreatment Technologies

Caterpillar designed Tier 4 Interim products with Tier 4 Final standards in mind. To meet the additional 80 percent reduction in NOx emissions required by EPA Tier 4 Final/EU Stage IV emission standards, Caterpillar engineers only needed to add one new system to the already proven aftertreatment solution in use, Selective Catalytic Reduction (SCR).

Diesel Exhaust Fluid

Selective Catalytic Reduction utilizes Diesel Exhaust Fluid (DEF), which can be conveniently filled from ground level. Simply refill the DEF tank when you refuel. A gauge on the dash shows your fluid level. When you turn the machine off, a pump will automatically purge the DEF lines. A light located inside the rear engine compartment will turn off, telling you the purge is complete and that it is safe to turn off the electrical disconnect. If the engine/aftertreatment temperatures are high, a Delayed Engine Shutdown will activate automatically to cool the machine and then purge the lines. For complete aftertreatment information, please refer to your machine's Operation and Maintenance Manual.

Power Train

Standard Automatic Differential Lock/Unlock monitors machine and application parameters to unlock/re-lock the differential during operation, improving production and enhancing comfort while protecting the power train.
Full Electronic Clutch Pressure Control optimizes inching modulation for smooth shifts and directional changes.
Programmable Autoshift option simplifies operation by allowing you to program the transmission to shift at optimal points to match your application.
New standard Economy Mode can be turned on to help save fuel by reducing engine speed so the machine works in a more efficient range. The average fuel savings is up to 10 percent, depending on the application.
Power Shift Countershaft Transmission maximizes power to the ground.
Engine Over-Speed Protection prevents downshifting until an acceptable safe travel speed has been established.

Front and Rear Axles

The sealed spindle keeps front axle bearings lubricated and protected from contaminants. The Cat “Live Spindle” design places the larger tapered roller bearing on the outside, where the load is greater, extending bearing life. A bolt-on modular rear axle improves serviceability and contamination control with easy access to differential components.

Hydraulic Brakes

Oil-bathed multi-disc service brakes are hydraulically actuated for smooth, predictable braking and lower operating costs. Brakes are located at each tandem wheel and have a large total brake surface area to give you dependable stopping power and longer life.

Structures and Drawbar-Circle-Moldboard

Caterpillar designs motor grader frame and drawbar components to give you performance and durability. The one-piece forged steel circle stands up to high stress loads, and a sacrificial wear system helps keep your service time and costs down. The articulation hitch features a large tapered roller bearing to carry loads evenly and smoothly. It is sealed to prevent contamination and a locking pin prevents articulation for safety during service or transport.

Easy Maintenance for More Uptime

The drawbar, circle and moldboard are designed to make it easy to keep the components tight. One person can easily adjust or replace the patented top-adjust drawbar wear inserts from the top of the drawbar plate, reducing downtime to save you money. Durable nylon composite wear inserts maximize circle torque and component life. Sacrificial brass wears strips between the blade mounting group and moldboard can be easily adjusted and replaced. The Shimless Moldboard Retention System uses vertical and horizontal adjusting screws to keep moldboard wear strips aligned for reduced blade chatter and precise blade control.

Blade Angle and Moldboard

An aggressive blade angle, optimized moldboard curvature and large throat clearance help you work more efficiently by allowing material to roll more freely along the blade. Heat-treated rails, hardened cutting edges and end bits, and heavy duty bolts to give you greater moldboard reliability and long service life. The link bar allows extreme moldboard positioning for easier bank sloping and ditch cutting/cleaning.

Hydraulics

Responsive Hydraulics

A proven load-sensing system and advanced electro-hydraulics give you superior implement control and responsive hydraulic performance that helps make your operator's job easier. Continuously matching hydraulic flow/pressure to power demands creates less heat and reduces power consumption.

Consistent, Predictable Movement - Proportional Priority Pressure-Compensating (PPP-C) valves have different flow rates for the head and rod ends of the cylinder, so you can count on consistent, predictable implement response.
Balanced Flow - Hydraulic flow is proportioned to give you confidence that all implements will operate simultaneously without slowing the engine or speed of some implements.

Blade Float

Allows the blade to move freely under its own weight. By floating both cylinders, the blade can follow the contours of the ground. Floating only one cylinder permits the toe of the blade to follow a hard surface while the operator controls the slope with the other lift cylinder.

Independent Oil Supply

Large, separate hydraulic oil supplies prevent cross-contamination and provide proper oil cooling, which reduces heat build-up and extends component life. Cat XT™ hose allows high pressures for maximum power and reduced downtime.

All Wheel Drive (AWD)

If you work in soft underfoot conditions where traction can be a challenge, optional All Wheel Drive (AWD) can give you the additional power to the ground you need to work more efficiently in mud, gravel, sand or snow. The added traction helps reduce sliding on side slopes.

Dedicated left and right pumps give you more precise hydraulic control. The infinitely variable pumps and motors maximize torque in each gear.
AWD automatically increases horsepower to maximize your power to the ground.
Standard Hydrostatic Mode disengages the transmission and provides hydraulic power to the front wheels only. Infinitely variable ground speed between 0-8 km/h (0-5 mph) is ideal for precise finish work.
Cat Steering Compensation System enables a “powered turn” by adjusting the outside front tire speed up to 50% faster than the inside tire. This gives you improved control, reduces surface damage and greatly reduces turning radius in poor underfoot conditions.

Integrated Technologies

Cat Connect makes smart use of technology and services to improve your job site efficiency. Using the data from technology-equipped machines, you'll get more information and insight into your equipment and operations than ever before. Cat Connect technologies offer improvements in these key areas: Equipment Management - increase uptime and reduce operating costs. Productivity - monitor production and manage job site efficiency. Safety - enhance job site awareness to keep your people and equipment safe. Featured Cat Connect technologies include:

Link

Link technologies provide wireless capability to machines enabling two-way transfer of information collected by on-board sensors, control modules, and other Cat Connect technologies using off-board apps, such as our VisionLink software.

Product Link™/VisionLink®

Product Link takes the guesswork out of equipment management. Track location, hours, fuel usage, productivity, idle time, diagnostic codes and more through the online VisionLink interface. Manage your fleet in real time so you can maximize efficiency, improve productivity, and lower operating costs.

Grade

Grade technologies combine digital design data, in-cab guidance, and automatic blade controls to enhance grading accuracy, reduce rework, and lower costs related to production earthmoving and rough, fine and finish grade applications.

Cat Grade Control Cross Slope

Cat Grade Control Cross Slope is an optional fully integrated, factory installed system that helps your operator improve grading efficiency and more easily maintain accurate cross slopes. The system automatically controls one side of the blade, reducing manual operator inputs by as much as 50 percent. Experienced operators can maintain peak efficiency levels throughout more of the work day, while less experienced operators can be more productive faster. The system is job-ready from day one, and scalable for the future with AccuGrade™ upgrade kits that provide additional 2D and/or 3D control.

Cat AccuGrade

AccuGrade is an optional dealer-installed grade control system that provides higher accuracy capabilities to the Cat Cross Slope system by adding Sonic, Laser, GPS, and/or Universal Total Station (UTS) technology when the job requires. In-cab guidance helps operators work more confidently and get to grade faster, in fewer passes, using less material, improving productivity and accuracy by nearly 50 percent over conventional methods. Grade stakes and checkers are minimized, making the job site safer and more cost effective. An AccuGrade Attachment Ready Option can be ordered as a factory or dealer-installed option. It includes built-in mounting points and internal wiring for easy installation of the AccuGrade system.

Safety

Operator Presence Monitoring System

Standard system keeps the parking brake engaged and hydraulic implements disabled until the operator is seated and the machine is ready for operation.

Speed Sensitive Steering

Standard function makes steering less sensitive as ground speed increases for greater operator confidence and control.

Secondary Steering System

Standard feature automatically engages an electric hydraulic pump in case of a drop in steering pressure so the operator can steer the machine to a stop.

Hydraulic Lockout

Disables all implement functions while still providing machine steering control. This standard safety feature is especially useful while roading.

Brake Systems

Brakes are located at each tandem wheel to eliminate braking loads on the power train. Redundant brake systems utilize accumulators to enable stopping in case of machine failure.

Walkways and Grab Rails

Perforated steel tandem walkways and convenient grab rails give you a sturdy platform when moving on, off and around the machine.

Circle Drive Slip Clutch

Protects the drawbar, circle and moldboard from shock loads when the blade encounters an immovable object. This standard feature also reduces the possibility of abrupt directional changes in poor traction conditions.

Blade Lift Accumulators

Help absorb impact loads to the moldboard by allowing vertical blade travel. This optional feature helps reduce wear and aids operator safety.

M Series 3 Safety Features

Optional rearview camera with in-cab monitor
New optional seat belt indicator light reminds operator to fasten safety belt
Grouped, ground level service points
Laminated front window glass
Optional LED Lighting
Ground-level electrical disconnect switch
Ground-level engine shutoff switch
Anti-glare paint eases night operation
Optional front and rear fenders

Work Tools and Attachments

Moldboard Options

The 160M3 motor grader comes equipped with a 3.7 m (12 ft) moldboard. Optional 4.3 m (14 ft) and 4.9 m (16 ft) moldboards are also available.

Ground Engaging Tools (GET)

A variety of tools are available from Cat Work Tools, including cutting edges, graderbits and end bits, all designed for maximum service life and productivity.

Front Mounted Groups

A front mounted push plate or front lift group are available. The front lift group can be combined with a front dozer blade or front scarifier for added versatility.

Rear Ripper/Scarifier

Made to penetrate tough material fast and rip thoroughly for easier movement with the moldboard. The ripper includes three shanks (with holders for five). Nine scarifier shanks can also be added for additional versatility.

Snow Removal Work Tools

Snow plow, snow wing and mounting options increase machine versatility and utilization throughout the year.

Smart Machine Systems

Cat Messenger, combined with full systems integration, enhances diagnostic capability for quick analysis of critical data.
Electronic Technician (Cat ET) lets service technicians access stored diagnostic data and configure machine parameters through the Cat Data Link.
Low Battery Elevated Idle raises idle speed when low system voltage is detected, ensuring adequate system voltage and improving battery reliability.
Automatic Engine Deration protects the engine by automatically lowering engine torque output and alerting the operator if critical conditions are detected.

Serviceability and Customer Support

Cat motor graders are designed to help you increase uptime and reduce costs. Grouped service points and extended service intervals save maintenance time. New optional LED lights in the left hand compartment makes it more convenient to service the machine in low light.

Unparalleled Dealer Support

When it comes to supporting you, Cat dealers are second to none. From machine selection and purchase to maintenance support and rebuilds, Cat dealers have the experience and capabilities to help keep you up and running.

Sustainability

Fuel Efficiency

Integrated machine systems and technologies improve productivity for greater accuracy, allowing the machine to do more work per gallon of fuel.
New Economy Mode feature allows the machine to work in the most efficient engine speed range to help reduce fuel use.

Green House Gas Emissions

Reduced fuel consumption means reduced CO2 emissions.
M Series 3 Motor Graders meet U.S. EPA Tier 4 Final/EU Stage IV emission standards.

Material Efficiency and Lifecycle Costs

Replaceable wear parts save maintenance time and cost, and extend major component life.
Major components are built to be rebuilt, eliminating waste and saving customers money by giving the machine and/or major components a second - and even third - life.
Approximately 95% of machine materials can be recycled (ISO 16714) to conserve valuable natural resources and further enhance machine end-of-life value.

Sound

• Reduced engine noise and quieter cabs mean lower operator and spectator sound levels.

Safety

Ecology drains help make draining fluids more convenient and help prevent spills.
Cartridge style hydraulic fluid filters provide safe clean draining of filters prior to replacement, helping to prevent fluid spills.
A variety of safety features help safeguard operators and others on the job site.

Equipment

160M3 AWD Standard Equipment

POWER TRAIN

Air cleaner, dual stage, dry type, diesel, with automatic engine derate and automatic dust ejector, service indicator through Cat Messenger
Air-to-air after cooler (ATAAC)
Belt, serpentine, automatic tensioner
Brakes, oil disc, four-wheel, hydraulic
Demand fan, hydraulic, swing-out
Diesel exhaust fluid tank, 22.0 L (5.8 gal) ground level access, and sediment drain
Differential Lock/Unlock, Automatic
Drain, engine oil, ecology
Economy mode
Electronic over speed protection
Engine, C9.3 with ACERT Technology, U.S. EPA Tier 4 Final/EU Stage IV emission standards
Fuel tank, 394 L (104 gal), ground level access and sediment drain
Parking brake - multi-disc, sealed, oil-cooled
Priming pump, fuel
Rear axle, modular
Sediment drain, fuel tank
Tandem drive
Transmission, 8F/6R, powershift, direct drive, Advanced Productivity Electronic Control Strategy (APECS)

ELECTRICAL

Alarm, back up
Alternator, 150 ampere, sealed
Batteries, maintenance free, heavy duty, 1125 CCA
Breaker panel, ground accessible
Cab harness and electrical hydraulic valves
Electrical system, 24V
Grade Control Ready - Cab harness, software, electrical hydraulic valves, bosses and brackets
Lights, roof-mounted roading, reversing, LED stop and tail
Product Link
Starter, electric

OPERATOR ENVIRONMENT

Accelerator
Air conditioning with heater
Arm and wrist rest, electronically adjustable
Articulation, automatic Return-to-Center
Cat Messenger operator information system
Centershift pin indicator
Coat hook
Cup holder
Display, digital speed and gear
Doors, left and right side with wiper
Gauge, machine level
Gauge cluster (analog) - fuel, articulation, engine coolant temp, engine RPM, hydraulic oil temp, regen, DEF
Hour meter, digital
Joystick hydraulic controls right/left blade lift with float position, circle drive, blade sideshift and tip, centershift, front wheel lean, articulation and power steering
Joystick, adjustable armrests
Joystick gear selection
Joystick hydraulic power steering
Ladders, cab, left and right side
Lights, night time cab
Mirror, inside rearview, wide angle
Power port, 12V
Radio Ready, Entertainment
ROPS cab, sound suppressed 70 dB(A)
Seat, cloth-covered, comfort suspension
Seat belt, retractable 76 mm (3 in)
Storage area for cooler/lunchbox
Throttle control, electronic
Windows, laminated glass: - fixed front with intermittent wiper - door with intermittent wipers (3)
Windows: tempered: - left and right side wipers - rear and intermittent wiper

FLUIDS

Antifreeze
Extended Life Coolant to -35° C (-30° F)

TIRES, RIMS AND WHEELS

Partial allowance for tires on 254 × 607 mm (10 × 24 in) multi-piece rims is included in the base machine price and weight

OTHER STANDARD EQUIPMENT

Accumulators, brake, dual certified
Anti-glare paint
Bumper, rear, integrated with hitch
CD ROM Parts Book
Clutch, circle drive slip
Cutting edges: - 152 × 16 mm (6 × 5/8 in) - curved DH-2 steel - 19 mm (3/4 in) mounting bolts
Doors (3), engine compartment, locking
Drawbar - 6 shoes, replaceable wear strips
Electrical hydraulic valves, hydraulic lines for base 8 functions
Endbits: - 16 mm (5/8 in) DH-2 steel - 19 mm (3/4 in) mounting bolts
Fluid check, ground level
Frame, articulated, with safety lock
Ground level engine shutdown
Hammer (emergency exit)
Horn, electric
Hydraulic lines for base functions
Lockout, hydraulic implement (for roading and servicing)
Moldboard
Mounting, cab roof accessories
Pump, hydraulic, high capacity, 98 cm³ (6 in³)
Radiator, cleanout access (both sides with swing doors)
Secondary steering
Serviceability, LH side
S·O·S℠ ports: engine, hydraulic, transmission, coolant, fuel
Tandem walkway/guards
Tool box

160M3 AWD Optional Equipment

ELECTRICAL

Alternator, 280 ampere
Batteries: extreme duty, 1,400 CCA
Lights: Headlights, high
Lights: Headlights, low
Lights: Working lights, basic
Lights: Working lights, plus, LED
Lights: Warning: beacon or strobe
Lights: Mounting for warning light

GUARDS

Articulation guard
Fenders, front, AWD
Fenders, rear
Front axle guard
Sound suppression (bottom)
Sound suppression (enclosure)
Transmission

OPERATOR ENVIRONMENT

Mirrors, outside: heated 24V
Mirrors, outside: mounted
Comfort Plus Arrangement
Comfort Premium Arrangement

POWER TRAIN

Precleaner, snow
Starter, extreme duty, 1,000 Amps
Transmission, autoshift

OTHER ATTACHMENTS

AccuGrade ARO
Integrated cross slope
Accumulators, blade lift
Camera, rearview
Cat Product Link 321SR
Cat Product Link 522
Drain, ecology, engine Wiggins
Heater, engine coolant: 120V
Heater, engine coolant: 240V
Hydraulic arrangements with one or more additional hydraulic valves are available for rear ripper, dozer, snow plow and snow wing.
Snow wing mounting, frame ready
Starting aid, ether
Reversing fan, automatic or manual

WORK TOOLS/G.E.T.

Blade extension, left hand, 610 mm (2 ft)
Blade extension, right hand, 610 mm (2 ft)
Counterweight
Cutting edges, curved
Endbits, overlay
Front lift group, mounting
Front lift group, mechanical
Grader bit, narrow and super penetration
Mid-Mount Scarifier, Package
Moldboard: 4267 mm × 610 mm × 22 mm (14 ft × 24 in × 7/8 in)
Moldboard: 4267 mm × 686 mm × 25 mm (14 ft × 27 in × 1 in)
Moldboard: 4877 mm × 686 mm × 25 mm (16 ft × 27 in × 1 in)
Push plate
Ripper, rear
Ripper tooth
Scarifier, front
Snow Arrangement
Snow Wing Ready Package
Tow hitch

MACHINE ARRANGEMENTS

Canadian Arrangement
European Arrangement
TUV Roading Arrangement

OPTIONAL TIRE ARRANGEMENTS

Rim Size - 9 × 24; Wheel Group - Single-Piece; Tires - 14.0R24
Rim Size - 13 × 25; Wheel Group - Single-Piece; Tires - 17.5R25
Rim Size - 10 × 24; Wheel Group - Multi-Piece; Tires - 14.0R24
Rim Size - 10 × 24; Wheel Group - Multi-Piece; Tires - 14.0-24
Rim Size - 14 × 25; Wheel Group - Multi-Piece; Tires - 17.5R25
Rim Size - 14 × 25; Wheel Group - Multi-Piece; Tires - 17.5-25
Note: Consult your dealer for individual tire width, size and brand.

160M3 AWD

160M3 AWD

View Product Downloads

Related Products

Attachments

Specifications

Overview

Engine

Power Train

Hydraulic System

Operating Specifications

Service Refill

Frame

Tandems

Moldboard

Blade Range

Ripper

Scarifier

Weights

Weights - AWD

Dimensions

Standards

Benefits & Features

Operator Station

Machine and Implement Controls

Engine

Emissions Technology

Power Train

Structures and Drawbar-Circle-Moldboard

Hydraulics

All Wheel Drive (AWD)

Integrated Technologies

Safety

Work Tools and Attachments

Smart Machine Systems

Serviceability and Customer Support

Sustainability

Equipment

160M3 AWD Standard Equipment

160M3 AWD Optional Equipment

News & Events

Promotions

Social Media

Branch Locations

Services

Technology

Finance

This website is using cookies.

Please share your feedback on Finning.com!